admin-it
About
- Username
- admin-it
- Joined
- Visits
- 3,017
- Last Active
- Roles
- Administrator
Comments
-
https://www.treadmilldoctor.com/dc-amp-draw If you are in need of parts you can use this discount code below: Discount Code - COPY AND PASTE this code, 1982 in the discount code box for a 5% discount off your order,
-
You will need a new roller sleeve. https://www.treadmilldoctor.com/roller-sleeve-kit-2-1-4 Discount Code - COPY AND PASTE this code, 1982 in the discount code box for a 5% discount off your order,
-
Sounds your walking belt could be worn, how old is the belt and how often were you lubing the belt before that. Make sure the lube has no petroleum in it. If it does that could be a issue.
-
Did you check wire harness to make sure there is no cut wires in that 8 pin harness?
-
Maintenance free is not really maintenance free. We would like to refer you to this section: https://www.treadmilldoctor.com/keys-manual-says-to-use-only-lubenwalk-or-not-to-lube-kf then get you this link: https://www.treadmilldoctor.com/world-f…
-
Really sounds like maybe the walking belt is the issue, the reason for the burning smell at no incline is because the unit is pulling more current to move your body weight, compare to when your on incline your body weight forces belt to move easier…
-
call me 888-362-1105 then enter Ext 331 and ask for Jim , if you have any questions.
-
3 blinks is a overload caused by to much current draw from the motor which most likely means that the walking belt is worn out. If you purchase a new belt below is a discount code to save 5% Discount Code - COPY AND PASTE this code, 1982 in the di…
-
Hello! We apologize for the delay in returning your query! Here are some tests you can try to test out your treadmill: https://www.treadmilldoctor.com/shuts-down-during-a-workout If these do not help let us know and we will go from there!
-
Could that motor is over heating and causing unit to shut down, I would do a amp draw test and see what the amps are with load and without.
-
Hello! Sorry it took so long to reply - have you had a chance to try and re-callibrate? https://www.treadmilldoctor.com/incline-calibration-instructions
-
Your deck is worn out, and it has a dead spot on it, most likely you would need to replace the deck and the walking belt since they are both so old. normal life for a belt is about 7 to 8 years. The walking belt is $129.99 and the deck is $199.99 pl…
-
Leave the walking belt very loose and just calibrate unit, once unit is calibarted then adjust your walking belt. In the futrue if you need any other parts below is a discount code to save 5%. Discount Code - COPY AND PASTE this code, 1982 in the d…
-
Congraulations
-
I would contact matrix direct for that info.
-
what model treadmill?
-
Then it could be just weak motor and that would have to be replaced.
-
I would try to lube belt and see if that helps, but it looks like you have a weak motor. LUBE DECK
-
Heart rate grips are a hit or miss, sometimes if you wet your palms with warm water it will pick up your heartrate.
-
Treadmill Rescue Kit Here is something that we design for customers who need a console but find the consoles are no longer available, works on any treadmill if the Drive Motor still works. Speed is 0 to 10mph Unit will allow unit to incline, but wi…
-
could be a motor or front roller
-
Could be in the console itself.
-
Sounds like its in the incline rack assembly that supports treadmill, You can try to lube the pivot points on the incline frame itself and see if that helps.
-
When it shuts down does the screen go blank. does it trip a breaker in house?
-
I would contact xterra ,and let them know console did not fix issue.
-
1) Remove the safety key 2) Press and hold down the Start and Fast (speed up) buttons with one hand and replace the safety key with the other. Continue to hold the Start and Fast key until the window displays “Factory settings”, then press the en…
-
It may if the are available from icon fitness
-
Could be in the bearing or the motor brushes.
-
Do you have the complete model number its located on a sticker down on the frame close to the floor
-
I would check all your connections, sounds like maybe a motor controller has gone bad. https://support.johnsonfit.com/resource.php?url=http://productload.johnsonfit.com/inc/uploaded_media/96bda51ea47667216e8c48afeb8cdf4e/service_guide/310d78f34cd9df…