jimbo97
About
- Username
- jimbo97
- Joined
- Visits
- 108
- Last Active
- Roles
- Member
Comments
-
Do you have the complete model number its located on a sticker down on the frame close to the floor when you fold unit up. Also you can look under the hood cover and there is a piece of paper inside a envelope that has the model number on the paper.
-
You may have to reinstall the software by purchasing a CNSL REPROG THUMB DRIVE and they are $96.55. To order please call me 888-362-1105 then enter Ext 331 and ask for Jim.
-
Sounds like the motor controller has gone bad, You would need Part Number 248187, Use this Discount code 1982 at checkout for a 5% discount on your order.
-
What is the serial number off treadmill?
-
Sounds like the running belt will need to be replaced. https://www.treadmilldoctor.com/aerobics-pacemaster-pro-plus-walking-belt Once you've added items to your Cart, and you are ready to Check out and you put all your shipping info in. Use this cod…
-
Most likely you would need a new console.
-
You can try to unplug ribbon cable from keypad to main circuit board, then clean the ends and plug it back in. If that does not work then you would have to look into purchasing a new console. And they are around $599.99.
-
Trying unpluging the ribbon cable and clean the end off then plug back in and see what that does.
-
Sorry we do not carry any motor for those unit or any motor that would work in those units.
-
Could be maybe a loose drive belt
-
No sorry you cannot.
-
You just answer your own question, when you switch wires you can get unit to come down. Once you've added items to your Cart, and you are ready to Check out and you put all your shipping info in. Use this code 1982 at checkout for a 5% discount on y…
-
Normally the bolt goes there the roller on the right side, you can always take a picture of the front roller assembly so we can get a better look at it.
-
https://www.treadmilldoctor.com/dc-amp-draw
-
You would need to contact nordictrack for that help
-
As you can see front roller is held in place with bolts on both sides
-
https://www.iconservice.com/model/parts?modelNumber=25046&version=0
-
Sounds like a bad console, you may have to replace it ,if they are still available.
-
Your motor controller has gone bad, below is a link for the new controller and a discount code to save yourself 5%. https://www.treadmilldoctor.com/nordictrack-viewpoint-treadmill-motor-control-board-4 Once you've added items to your Cart, and you a…
-
Sounds like you have a drive motor issue.
-
Should have came in the owners manual that came with treadmill.
-
Yes you can very easy.
-
No that motor will not work, The motor you need is $229.99 plus shipping. To order please call me 888-362-1105 then enter Ext 331 and ask for Jim.
-
Really sounds like a weak motor, try starting it and run it to 2.0mph and with hood cover off try to put pressure against flywheel and see if you can stop it. if you can pretty easy then its a motor. Once you've added items to your Cart, and you are…
-
https://www.treadmilldoctor.com/precor-c932i-vertical-tread-120v-hhhr-axgt-treadmill-5-button-snap-dome-ppp000000048778101 Once you've added items to your Cart, and you are ready to Check out and you put all your shipping info in. Use this code 1982…
-
https://www.treadmilldoctor.com/how-to-measure-a-walking-belt. ADJUST TENSION ON BELT
-
Sounds like a console issue, you can unplug the ribbon cable that goes from buttons to main console and clean the ends real good then plug back in and see if that helps
-
The walking belt is worn out. Once you've added items to your Cart, and you are ready to Check out and you put all your shipping info in. Use this code 1982 at checkout for a 5% discount on your order.
-
360694 CNSL REPROG MICRO SD CARD
-
Your problem is that the main pulley on front roller has broken loose and move over, so your drive belt is not even on pulley on front roller, You will need to replace entire front roller which comes with the new pulley.