admin-it
About
- Username
- admin-it
- Joined
- Visits
- 3,282
- Last Active
- Roles
- Administrator
Comments
-
Hi! This could simply be too much friction on your belt - have you lubed lately?
-
What is your model number? Are you getting a specific error message and have you tried to recalibrate?
-
With the burning smell you need to check for a short in the motor. You can run the motor with an independent power source like a fully-charged cordless drill battery to see if the symptoms are the same.. https://www.treadmilldoctor.com/motor-testing
-
If you have your model number handy we can help find your console!
-
Good luck with your repair!
-
https://www.treadmilldoctor.com/pacemaster-gold-elite-treadmill-drive-motor-ap2drmtrm Once you've added items to your Cart, and you are ready to Check out and you put all your shipping info in, you then can put this Discount Code ( 1982 ) in the Di…
-
you tested the motor with an external power source? all cables are clean and checked with volt meter? You have a new MCB and the questions above are yes then it sounds like your console is going
-
Ouch that does sound incredibly painful! Technology is great until it works against us!!!
-
I am glad you were able to get it off without damage! Great job!
-
Great job on figuring out the issue!!! What is your model number so I can get you the correct part number?
-
ok - if you look in your manual on the top of page 23 you can see where you took out the 3 screws - it then says to carefully pivot the motor hood off and you can see the motor hood swing out for some reason I cannot attach the manual here - send m…
-
You can contact this company about sending in your parts to be repaired. https://fitnesselectronicrepairs.com 954-578-0900 if you tested the motor and that runs with a battery , then lower board is bad.
-
What is your complete model number?
-
Yes we think the console is bad on the one Robert asked about - did you check your voltage from your harness to your console?
-
Hello! I am sorry to say that part is no longer available which I am sure you already know! I did not have any luck with my search, hopefully, you will find a machine you can use for parts! Here is another forum you could try and post for help!…
-
The guy above had 4 additional screws under the unit. What is your complete model number and I will look up the diagram?
-
Hello! You can check out our reviews for the best treadmills to purchase! https://www.treadmilldoctor.com/bestbuyawards-treadmill
-
MY RUNNING BELT STOPS WHEN I STEP ON IT Here are a few things you can look into to see why your running belt is stopping when you walk on treadmill. • Let’s remove the hood cover on your treadmill. • Now run the treadmill at 2.5mph with…
-
What is your serial number?
-
Hello and good morning! You might just need to adjust the tension! Check out these videos for direction! https://www.treadmilldoctor.com/walking-belt-adjustment
-
Please try this! https://www.treadmilldoctor.com/icon-calibration-mc2100
-
Belt last normally about 5 to 6 years.
-
https://www.fitnessrepairparts.com/cart/ViewItem/6013552
-
You have a bad console.
-
I can only imagine!!! The automatic decline is set up not only as a safety feature, but also to help you work different leg muscles for extra toning and calorie burnout. No, it is not possible to delete the factory settings - you can only adjust m…
-
what is your complete model number off unit?
-
Based on these pictures it looks like you just need to replace your walking belt! If you have a model and serial number we will get you a link to the correct size!
-
Did you move your machine? Would it be possible to unplug your machine, wait a full minute, and then replug back into the wall? It could be that the lower board is not sending voltage to the console and the only way to know this is if you have a vo…
-
Would it be possible to provide pictures of both the belt and deck underneath the belt? I would dislike intensely having to tell you to replace both but for sure we are looking at replacing the belt...
-
Did the pulley stop the drive belt?