admin-it
About
- Username
- admin-it
- Joined
- Visits
- 3,282
- Last Active
- Roles
- Administrator
Comments
-
That is great news! Glad to hear you are up and running!
-
https://www.treadmilldoctor.com/motor-testing
-
Error 425 Runaway An analog detection circuit indicated that the voltage across the power FET stayed low. 1. replace lower board 2. replace motor The lower board is no longer available.
-
If that does not help it could be the walking belt is worn out.
-
I would lube the belt very good.LUBE DECK
-
Hey and good morning! What is your complete model number? Let's remove the hood cover and check: 1. When the running belt stops does the Drive Motor also stop? -If yes then it could be a weak Drive Motor or bad Motor Controller. 2. When the runn…
-
Were you able to ascertain the noise on your bike?
-
when there is no power unit should have very little to no resistance The lower board may still have a charge in the capacitors which can cause motor to move a little at times, but not much.
-
Hello and yes the power could be low. Try this: https://www.treadmilldoctor.com/dc-amp-draw then try: https://www.treadmilldoctor.com/motor-testing Great job on narrowing down the issue!
-
Happy Friday! Well, that is sad to hear the manufacturer cannot help! Have you tried to recalibrate? Calibration Procedure 1. Remove the Safety Key. 2. Press and hold Start and Speed _ buttons and at the same time replace the Safety Key. Continu…
-
Good morning! you can get a screeching noise by the pulley loosing its grip on the front roller. We have instructions at this address for you to use to test out this theory - https://www.treadmilldoctor.com/belt-slipping-kf
-
I apologize for my levity! Here is what I found in your service manual pg 22... To change the resistance of the pedals...: Touch Manual Start and begin pedaling. You can change the resistance of the pedals by pressing one of the numbered Resist…
-
I heard that Treadmill Dr had a pretty good forum lol What is your model and serial number?
-
Hate to hear their customer service was not up to par! I hope we can help! You will have to loosen the side covers over the wheel (remove if possible) and hand crank the pedal while you are looking inside. Until you open it up, it is just a guessin…
-
MY RUNNING BELT STOPS WHEN I STEP ON IT Here are a few things you can look into to see why your running belt is stopping when you walk on treadmill. • Let’s remove the hood cover on your treadmill. • Now run the treadmill at 2.5mph with…
-
The drive belt will need to be replaced on your machine.
-
When belt stops, does motor & drive belt and front roller still spin?
-
Here is the number for Spirit - 1-800-258-8511 We apologize for not being able to help you out more with your issue!
-
Let us know how it goes!
-
The light on the controller just lets you know you have ac voltage coming into treadmill. Again test for 8 to 12vdc on the black wire & red wire . if you have proper voltage console is bad if not motor controller is bad, We see this all the time…
-
Sounds like it could be either in the front or rear roller, what you can do is take off hood cover run unit by itself and when the noise happens , take a little wd-40 and try spraying some into the bearing on the front roller on each side where the …
-
It could be that the lower board is not sending voltage to console and the only way to know this is if you have a voltmeter and test the end of console that plugs into the console. You need to test the red wire & the black wire and should have…
-
There is a reed switch under the motor hood along with a magnet on the left side of the pulley. The pulley has to be turned until the magnet is aligned with the reed switch. The gap between the magnet and the reed switch should only be 1/8 inch. The…
-
Did you lube correctly when replacing the belt? If so - check the belt guides under the treadmill. If they are too aggressively pushing into the belt, it can cause a whining noise. You can just bend the guides if needed. Also - you can get a scr…
-
What is your complete model number? Do not give up! We sure won't!
-
please go into engineering mode to find out exactly which buttons do not work Engineering mode 1. Remove the tether cord. 2. Press and hold the START, ENTER, and STOP buttons and replaced the tether cord. 3. The display will say ENGINEERING MODE. …
-
Would it be possible for you to supply the serial number for your machine?
-
The wire harness is the main harness the comes up from The motor controller up the right upright and plugs into console. https://www.iconservice.com/model/parts?modelNumber=PFTL60009&version=0
-
Do you put safety key back in place on unit, if safety key is not in place then unit will not light up and turn on. also make sure main harness coming down from lower board and runs up right side upright has not come unpluged.
-
that sounds great! hopefully it is just disconnected!