admin-it
About
- Username
- admin-it
- Joined
- Visits
- 3,114
- Last Active
- Roles
- Administrator
Comments
-
Here are a few tests you can run! https://www.treadmilldoctor.com/belt-moves-to-one-side Let us know if this helps!
-
here is the link for the motor controller! https://www.treadmilldoctor.com/nordic-track-elite-zi-model-ntl118080-motor-control-board
-
If you have confirmed the belt and/or deck is not worn and the belts aren't too tight, you can test for a motor torque problem. Typically when we find a motor that has lost torque; it needs a new set of motor brushes. Motor demagnetization is not t…
-
Both are comparable and different enough to warrant further investigation! Both have lifetime guarantees on certain parts and have great reviews! https://aimworkout.com/treadmills/precor-932i-treadmill-review/ https://www.treadmilldoctor.com/sol…
-
Hello! We do not know where you can find that part. you will need to replace the console if it is available...
-
we cannot find that console - it is no longer available at the manufacturer
-
Sorry we do not have the computer instructions
-
the relay is part of the motor controller
-
A bad speed sensor will not prevent a motor from starting up and running. Still sounds like a motor controller issue or console is not sending signal down to controller.
-
Hello! Try this: https://www.treadmilldoctor.com/icon-calibration-mc2100
-
if the time does not start to count up then its a console issue have you checked your wires for voltage? tested the motor?
-
have you had time to perform any maintenance on the treadmill such as lubing the belt?
-
please check to make sure all wires are securely plugged in inside make sure there is no crimping in the wires It could be that the lower board is not sending voltage to the console and the only way to know this is if you have a voltmeter and can…
-
https://www.fitnessrepairparts.com/cart/ViewItem/6087989
-
I would need your complete model number to find you a console.
-
New treadmills are expensive! The great news is that with the holidays coming up you will be able to find a good deal! Best of luck!
-
Sounds like you might have a short... Here is a link for a test to see: https://www.treadmilldoctor.com/full-speed-upon-power-up-kf
-
Sounds like a motor controller has gone bad.
-
to double-check the first steps we did not discuss - did you make sure outlet has power - make sure plug is secure - make sure safety key is in place - make sure all wires are securely plugged in? you have already checked for voltage - if you have …
-
You should be able to lift the walking belt (with the treadmill unplugged) in the center of the treadmill about 3" without straining.
-
Hello! Here are some quick steps you can follow to see where your power issue might be! https://www.treadmilldoctor.com/symptom-d-o-a-treadmill Let us know if this helps!
-
It sounds like debris is caught up in your machine. Please stop the machine and carefully clean around it - I would also suggest a mat - we have a few to choose from here: https://www.treadmilldoctor.com/catalogsearch/result/?q=mat&search=searc…
-
https://www.treadmilldoctor.com/treadmill-review-brand-index
-
Hello! You have to unbolt the 4 bolts that go from the backside through the flywheel into the crank arm.
-
1st When the running belt stops does the Drive Motor also stop? If yes then it could be a weak Drive Motor or bad Motor Controller. 2nd When the running belt stops does the Drive Motor continue to run and also does the drive belt continue to run? I…
-
Hello and good morning to you! You would definitely need to recalibrate. What is your model and serial number?
-
Hello! What is your complete model number? Let's see what we can find!
-
here you go! Phone: 877.654.3837 www.LifeSpanFitness.com
-
LOL you do - not me! I tend to tumble downhill!!!
-
Hello! If you have your complete serial number we can find you the bearings if they are still available! Looking forward to talking to you soon!