KevinC
About
- Username
- KevinC
- Joined
- Visits
- 785
- Last Active
- Roles
- Member
Comments
-
That seems a little high. what are you using to lubricate the belt/deck? and how much lube are you using?
-
No, it's not common for the belt to wear out that fast. let me know what the amp draw test results are.
-
it shipped on the 3rd. it should be there Wednesday this week
-
what is your order number?
-
I would start by lubricating the belt/deck https://www.treadmilldoctor.com/premium-lube-10-1-oz Here is a code you can use on the checkout page for a 10% discount (10offkevin)
-
There may be a calibration needed. can you get me the serial number of the treadmill?
-
Try lubricating the walking belt first. if that doesn't help then that belt should be replaced. (how long does it run before it shuts down?)
-
SB most likely means stuck button. there is no reset on this. Try massaging around all the buttons to see if you can get it to relax. if there are handle bar buttons, check them too.
-
You're welcome
-
here is a link for the controller; https://www.treadmilldoctor.com/NordicTrack-C-700-Treadmill-Motor-Control-Board-419478 and Here is a code you can use on the checkout page for a 10% discount (10offkevin)
-
this is a failed motor controller. can you get me the specific model number of the c700?
-
you are correct in leaving the red jumper in place.
-
on each side, there will be a screw coming up from the bottom. if you gently lay it on its side you'll be able to see the screws. they'll be in a recess hole.
-
I would reach out to ICON. their website still lists a console reprogramming SD card. 376027 CNSL REPROG MICRO SD CARD it is currently listed as out of stock but I would reach out to them anyway. The only other option I have is our Treadmill Rescue …
-
Usually this means that the console needs to be replace. Seems there is a software/firmware issue. can you get me the model number? I'll check for an update for this one.
-
good luck
-
I see this a lot with these. try this, make sure all bluetooth devices and wifi devices that are near the machine are all off except for the treadmill and your main wifi.
-
You're welcome
-
https://www.treadmilldoctor.com/nordictrack-incln-train-x11i-intera-motor-control-board-ntl240151-380915 and Here is a code you can use on the checkout page for a 10% discount (10offkevin)
-
This does sound like that lower board
-
have you disconnected on end of the incline motor and tried it?
-
This sounds as if there is a software issue with the console. does this machine have a SD card slot or USB slot on it?
-
Swap the red and black wires on that motor and let me know if you get the same results
-
Check the wire harness for damage. A lot of times when these machines are moved the main wire harness gets damaged and can cause this issue
-
here is a video on how to remove the flywheel https://www.treadmilldoctor.com/flywheel-removal
-
That's great. I've seen a lot of people try this with no luck.
-
This is a failed motor controller. if you can get me the specific model number I should be able to get you a link for the replacement.
-
Here is a code you can use on the checkout page for a 5% discount (5offkevin)
-
https://www.treadmilldoctor.com/proform-525-ct-pftl496170-motor-controller-386816
-
I would replace the motor first since it's know to not work from a battery. Then, the controller if it still doesn't work. The controllers output varies from about 15VDC @ .5 mph up to about 90+ or more at full speed with the motor connected. I've f…