admin-it
About
- Username
- admin-it
- Joined
- Visits
- 3,114
- Last Active
- Roles
- Administrator
Comments
-
GM! If you have your complete model number we can find out if those are still available! The model number its located on a sticker down on the frame close to the floor when you fold unit up. Also you can look under the hood cover and there is a pi…
-
GM! Does the treadmill operate normally without a person on the belt?
-
argh - try this! posted wrong info! https://www.dropbox.com/s/ryfvjajr7g5dp42/AFG 3.5AT SERVICE MANUAL.pdf?dl=0 https://www.dropbox.com/s/6j6fctlom6n42hl/AFG SPORT3.5 ELEVATION ISSUES.pdf?dl=0
-
just wow! yes! lucky dog!
-
Set the speed to 2.5 MPH. Let the treadmill run without anyone on the belt. Check to see if the speed is constant or if there is a variation. If there is no variation, step on the belt. If the speed slows down or speeds up, you may have an output pr…
-
GM! Hope your day is going great! Here is a link for calibration! let's see if this helps! https://www.treadmilldoctor.com/incline-calibration-instructions
-
Hey and good morning! Check the drive system to see if any part is scraping on another part. The belt should be aligned, pullies should be aligned, and the motor fan and the "fins" that move inside the speed sensor are all areas to check. Check the …
-
sounds like a worn belt or deck but here is a link for you to run a few tests to help figure out what is going on with your machine! https://www.treadmilldoctor.com/testing-for-speed-problems
-
does the unit run by itself with no one on it?
-
you might have blown the console depending on the voltage going through at the time - we do not ever recommend this action!
-
hey sorry - thought we answered earlier and just reread the whole thread! They are located on each side of motor, there is a little plastic door on each side and the brushes are inside there.
-
sounds good! sorry we don't have a diagram of the motor!
-
Hello! I am sorry to say that you will need to replace the motor - there is not a work-around for this... If you have your model number I can get you a link to the correct motor and use discount code 1679188172 when you purchase!
-
hey! not the motor model - the treadmill model number
-
hello! it sounds like the belt might should have been replaced first! check out this link: https://www.treadmilldoctor.com/shuts-down-during-a-workout
-
please check out this link to help you adjust! https://www.treadmilldoctor.com/walking-belt-adjustment
-
hello! if there are no access plugs or covers, you will have to completely disassemble the motor to get to them. do you have your model number - I can look up a diagram for you!
-
If you honestly want to keep the expense down and keep your beloved treadmill running you should order another deck from TMD. If you let us know your exact measurements and where your drill holes are located we can get an exact replacement for yo…
-
some treadmills have a stretch drive belt, as opposed to a drive belt that is tensioned by moving the motor or adjusting an idler. In this case you have to apply enough tension to the walking belt to keep the drive belt sufficiently tensioned and …
-
yours does not have a lube sensor if you have never changed your belt I am going to go out on a limb and say it is time for a belt change...
-
Space constraints are a pain for sure! I am leaning towards the TT8 for you! Best of luck with your new machine! Let us know how it works out!
-
here you go - hope this helps! https://www.dropbox.com/sh/smk9kmbzdh1bo42/AADb8IuJX9DDBezA7UQjawKla?dl=0
-
The review you referenced does not offer a lot of useful information! we believe the tt8 is a little bit better unit but both are good - basically though it all depends on how much the machines have been used and how well they have been maintained …
-
good morning! if you let unit by itself with no one on it, If it runs fine and does not shut off then you know that the running belt would need to be replaced also if you have a voltmeter and can test the red wire & the black wire you should h…
-
Hello! It is probably friction problems from the belt - older treadmills need regular belt maintenance to keep the load draw from being too heavy...
-
What is your serial number on your machine?
-
Hey and wow for all of the replacing! Great job! Sounds like you need to just adjust the tension... here are a few links: https://www.treadmilldoctor.com/walking-belt-adjustment
-
Hello from across the water most usually this is caused by a worn walking belt! here is a link to a few tests you can try to help! https://www.treadmilldoctor.com/shuts-down-during-a-workout
-
hello! here are a few things you can try if you are mechanically inclined - if not I suggest calling the Doc and getting a tech out there - 800-750-4766 opt 2 https://www.treadmilldoctor.com/symptom-d-o-a-treadmill
-
possibly (did you lube?) - if you would like to check out our grounding strap here is a link to a few different choices https://www.treadmilldoctor.com/catalogsearch/result/?q=grounding+strap Once you've added items to your Cart, and you are read…