admin-it
About
- Username
- admin-it
- Joined
- Visits
- 3,361
- Last Active
- Roles
- Administrator
Comments
-
The issue is the console had gone bad. below is a kit we sell for treadmills that need a console. Treadmill Rescue Kit Here is something that we design for customers who need a console but find the consoles are no longer available, works on any tr…
-
Really sounds like you have a bad motor, but may have been cause by a worn walking belt or also a bad controller.
-
Yes it could be if the gets hot it will shut down, make sure you keep the walking belt lube every 6 months. Use this code Cyber1982 at checkout for a 10% discount on your order.
-
https://www.treadmilldoctor.com/treadmill-motor-control-board-part-number-410270 You should lube the belt every 6 months- LUBE BELT https://www.treadmilldoctor.com/6-oz-slip-coat-lube Once you've added items to your Cart, and you are ready …
-
Sounds like your motor controller has gone bad. you can test the motor--https://www.treadmilldoctor.com/motor-testing https://www.treadmilldoctor.com/nordictrack-e3200-treadmill-motor-control-board Once you've added items to your Cart, and you are…
-
I would lube belt really good and let it soak in overnight. Thumping noise is normally the seam going over front and rear rollers.
-
https://www.treadmilldoctor.com/motor-testing
-
I would test the drive motor-https://www.treadmilldoctor.com/motor-testing
-
Sounds like it could be a weak motor, fue to maybe a worn walking belt.
-
The control board is no longer available for that unit. Treadmill Rescue Kit Here is something that we design for customers who need a console but find the consoles are no longer available, works on any treadmill if the Drive Motor still works. …
-
I email you a service mnual to help you.
-
I would test motor to see if its bad or good first. https://www.treadmilldoctor.com/motor-testing
-
Could be a very worn walking belt that can cause that , try loosen the walking belt so it does not run when you start unit up, only motor and front roller should spin, if you still get a LS1 then its a controller.
-
What happens if you run unit without anyone on it, does it do the same thing?
-
https://www.gympart.com/TSB/Precor/Treadmills/9.23_AYYA/D/Service_Manual-_9.23-_9.27_treadmill.pdf?srsltid=AfmBOorAZ0EkyH5ynaKVpiwOJi_W8Cm1Uy5epp77oM8qRf5P-gM0UTOs
-
Do you have the complete model number its located on a sticker down on the frame close to the floor when you fold unit up. Also you can look under the hood cover and there is a piece of paper inside a envelope that has the model number on the paper
-
Button maybe is worn out, you may need to replace keypad if available still. what is the serial off unit?
-
Sounds like it maybe a friction issue and I would think about replacing the belt or just try to lube it again and then lube soak into belt over night. If that does not help then replacing the running belt would be next. https://www.treadmilldoctor.c…
-
That is correct. Once you've added items to your Cart, and you are ready to Check out and you put all your shipping info in. Use this code 1982 at checkout for a discount on your order.
-
Its sounds like a upper console software failure, you would need to replace console if its available.
-
Its not a speed sensor its the motor controller.
-
https://www.treadmilldoctor.com/precor-c954i-commercial-tread-120v-gen-adey-treadmill-5-button-snap-dome-ppp000000048778101 Once you've added items to your Cart, and you are ready to Check out and you put all your shipping info in. Use this code 19…
-
Sounds like you have a keypad issue.
-
Did you calibrate the unit after installing mcb, also it could be a weak ftive motor also.
-
Could be either a bad motor controoler or drive motor. test the drive motor with a 12v or 18v battery. If motor runs then you have a bad motor controller, if it does not spin then its a drive motor. https://www.treadmilldoctor.com/motor-testing
-
Sorry we do not carry those parts, not sure of anyone does carry the parts
-
Could be either a bad drive motor or a bad motor controller. Test motor with a 12v or 18v battery. https://www.treadmilldoctor.com/motor-testing
-
I think you expecting to much from that treadmill. you can always recalibrate the incline so you will have peace of mind. https://www.treadmilldoctor.com/incline-calibration-instructions
-
I emailed you a wiring diagram.
-
Really sounds like a controller issue, below is a link to correct controller, https://www.treadmilldoctor.com/nordictrack-commercial-2950-ntl191190-treadmill-motor-controller-391855 Once you've added items to your Cart, and you are ready to Check ou…